搜索Maxwell 15.01之缺陷【轉發】
2017-06-27 by:CAE仿真在線 來源:互聯網
DE28651 In 2D magnetostatic when using a demagnetization link,
the mesh
in the source design and target designs must be identical.
However, if you
have added mesh operations or additional adaptive passes in
the target design
the software will enforce them causing the meshes to be
different. There is
currently no error message, but postprocessing solutions in
the target design
will fail (calculations may fail to evaluate and plots will
show no fields).
使用退磁計算時(2D靜態場),網格導入必須要完全相同。因此,在target
design中設置要注意。
DE32794 - In 2D transient using dynamic demagnetization should
not be used
in a design that is also using the advanced setting consider
core loss
effect on field. Results are unreasonable if you attempt to
combine these
2 functions.
動態退磁(2D瞬態場)功能與考慮鐵耗影響功能不能聯合使用。期待版本升級
DE33012 - In 2D transient models that do not have any windings
defined,
current density output to the postprocessor is incorrect. You
can add a
dummy winding to work around.
沒有繞組定義的2D瞬態場模型,進入后處理器中的電流密度是錯誤的。因此,
要添加一個虛擬繞組。
DE32768 - In 2D transient RZ models force calculations are
incorrect in
passive conducting objects with eddy effects activated.
2D瞬態場RZ模型中,則渦流引起的力計算錯誤。
DE34048 - In 3D transient when using the advanced feature
"Dynamic
demagnetization distribution", if a magnet is fully
demagnetized and operating
in the 4th quadrant with very high field levels, the B and H
field values
passed to the post-processor are not quite correct and would
show points
on the extension of the BH curve instead of the expected
location on a straight
line with Hc=0. This is a post-processing issue only, the
solver is using the
correct values and field solutions are otherwise
correct.
3D瞬態場中,使用動態退磁分布時,在第4象限中,后處理有誤。
DE29212 and DE34138 In 2D transient RZ designs, solid losses
are incorrect
in some cases due to an error in eddy current
calculations.
2D瞬態場RZ模型中,solid losses在一些渦流計算中不正確。
DE33891 and DE34082 In 3D transient with rotational motion,
when using a
magnet in the rotating part of the geometry that was defined
using a
cylindrical coordinate system, vector plots of the fields will
not show
correctly as the magnet rotates position. This is a post
processing issue
only, the field solutions are correct in the solver and other
quantities
(such as torque) are correct. You can avoid this issue by
defining the
magnet using a Cartesian coordinate system.
3D瞬態場旋轉運動時,使用直角坐標系定義永磁體方向較好。
In Maxwell 2D transient when working with demagnetization and
temperature
dependence, the temperature dependence only takes effect if
the radio button
in the BH entry dialog for the material is set to Intrinsic
before leaving
the dialog. If you have Normal selected then the thermal
modifier will be
ignored. Conversely, if you are not interested in temperature
dependence you
should convert to the Normal curve before you leave the BH
entry dialog.
In either case, you can enter the data in whichever form you
like, but you
must convert to Intrinsic for temperature dependence, or
Normal for all other
cases.
2D瞬態計算退磁和溫度依賴時,注意選擇相關的選項。
In 2D transient, dynamic demagnetization of nonlinear magnets
with conductivity
and eddy effect turned on in the magnets, cannot be combined
with coreloss
calculation with the advanced consider coreloss effect on
field setting turned
on and with eddy effects enabled in the winding. This
combination produces
incorrect results. The same combination will work if consider
coreloss effect on
field is turned off.
2D瞬態場中,非線性永磁體的動態退磁計算時(渦流開),不能與考慮鐵耗計算、繞組中的渦流效果
聯合使用。
轉自:http://blog.sina.com.cn/s/blog_4f850b690100ziwe.html
開放分享：優質有限元技術文章,助你自學成才
相關標簽搜索：Maxwell 15.01之缺陷【轉發】 Maxwell電磁仿真培訓 Maxwell培訓課程 Maxwell培訓班 Maxwell在線視頻 Maxwell教程 Maxwell軟件教程 Maxwell資料下載 電機設計仿真 Fluent、CFX流體分析 HFSS電磁分析 Ansys培訓 Abaqus培訓
編輯
